SPU NL 
Hand Boer "HDT-5"
The most powerful and durable in its class
(delivery anywhere in the world)
Home Make an order
Contacts Delivery
рисунокРоссия
Selection of equipment
picture
рисунок Video
All equipment presented on the site is unified with products manufactured in Russia.
Data for custom configuration of Pillar extractor
Equipment Price, $ (€)
Clamping plate 6.25 (6.25)
Cord 120 6.25 (6.25)
Cord 200 7.50 (7.50)
Cord 300 10.00 (10.00)
Bolt M10x55 0.63 (0.63)
Nut M10 0.25 (0.25)
Wrench 17 6.25 (6.25)

Example of complete set

  As examples, complete configurations of the Pillar Extractor are given.
  The number in the name of the cord, denotes its length in centimeters.
  Complete sets differ only in the length of the cord. The unique elements in the complete sets are the clamping planks made of thick-walled strip. Therefore, if there are other elements, you can order only them.

Attention!

 Pillar extractor very traumatic device. Be careful when performing captures. Just do not allow the cord to slip in your hand, because the surface of the rope as a result of wear, sharp elements may appear.
Pillar extractor PE-1.2
Clamping plate $ 6.25 х 4 = $ 25.00
(€ 6.25) х 4 = (€ 25.00)
Cord 120 $ 6.25 (€ 6.25)
Bolt M10x55 $ 0.63 х 4 = $ 2.52
(€ 0.63) х 4 = (€ 2.52)
Nut M10 $ 0.25 х 4 = $ 1.00
(€ 0.25) х 4 = (€ 1.00)
Wrench 17 $ 6.25 х 2 = $ 12.50
(€ 6.25) х 2 = (€ 12.50)
Price: $ 47.27 (€ 47.27)
Pillar extractor PE-2.0
Clamping plate $ 6.25 х 4 = $ 25.00
(€ 6.25) х 4 = (€ 25.00)
Cord 200 $ 7.50 (€ 7.50)
Bolt M10x55 $ 0.63 х 4 = $ 2.52
(€ 0.63) х 4 = (€ 2.52)
Nut M10 $ 0.25 х 4 = $ 1.00
(€ 0.25) х 4 = (€ 1.00)
Wrench 17 $ 6.25 х 2 = $ 12.50
(€ 6.25) х 2 = (€ 12.50)
Price: $ 48.52 (€ 48.52)
Pillar extractor PE-3.0
Clamping plate $ 6.25 х 4 = $ 25.00
(€ 6.25) х 4 = (€ 25.00)
Cord 300 $ 10.00 (€ 10.00)
Bolt M10x55 $ 0.63 х 4 = $ 2.52
(€ 0.63) х 4 = (€ 2.52)
Nut M10 $ 0.25 х 4 = $ 1.00
(€ 0.25) х 4 = (€ 1.00)
Wrench 17 $ 6.25 х 2 = $ 12.50
(€ 6.25) х 2 = (€ 12.50)
Price: $ 51.02 (€ 51.02)

Recommendations for the selection of the Pillar extractor

  If You plan to pull out the pillars with a diameter of up to 25 cm with a metal lever with a diameter of 3-4 cm, the most suitable will be the Pillar extractor PE-1.2, with a cord length of 120 cm, respectively.
  When uprooting wooden pillars with a diameter of 25 cm other wooden pillars, need the Pillar extractor PE-2.0 length of a cord 200 cm, respectively.
  If the diameter of the pillars to be pulled out more than 25 cm, you will need the Pillar extractor PE-3.0, with a cord length of 300 cm, respectively.
  Recruitment the Pillar extractor is made on the basis of what would be too long ends of a cord doesn't interfere.
  Below is a photo of the capture of the rod with a diameter of 12 mm, as an example of capturing thin elements, since this technique is not included in the video.
  At extreme loads, it is possible to slide the cord in the clamping plates. To eliminate the slip, tighten the bolting. It to tighten. Restoring the size of the loop with the unwinding and subsequent tightening of the clamping plates will not bring results. This is determined by the design of the cord. Noticing the slide, remove the load from the Extractor and tighten the bolting. picture
Контакты по всем вопросам: комплектация, применение, доставка и т.д.
tel. +7 (343‑88) 2‑27‑62
tel. +7‑967‑852‑42‑01
WhatsApp: +7‑992‑008‑72‑66
Viber: +7‑992‑008‑72‑66
npo-nl@npo-nl.ru

Weight-overall characteristics of the extractor elements
(all dimensions in the figures are in millimeters)
рисунок рисунок рисунок рисунок рисунок рисунок


Яндекс.Метрика